What gutter size do I need — 5-inch or 6-inch?

For most single-story Hickory-area homes, 5-inch K-style gutters are sufficient. Homes with steep roof pitches, large roof surfaces, or heavy tree coverage that channels concentrated flow often benefit from 6-inch gutters. We assess your roof and drainage patterns during the estimate and make a specific recommendation — we don't upsell size unless the run genuinely needs it.

Should I add gutter guards when I install new gutters?

New gutter installation is the ideal time to add guards — the gutters are already being set up correctly, the pitch is fresh, and the labor overlap keeps the total cost lower than doing it as a separate project. As a registered RainDrop® installer, we can bundle guard installation with any new gutter job.

Seamless Gutter Installation — Hickory, NC

New Gutters, Custom-Cut for Your Home

Seamless aluminum gutters fabricated on-site, sized correctly, pitched correctly, and color-matched to your fascia. No seams along the run — the most common failure point in sectional gutters — just one continuous piece per run.

🔩 Seamless — No Seam Leaks 🎨 Color-Matched to Your Fascia 📋 Free Written Estimates 🔒 Licensed & Insured

Get a Free Installation Estimate 📞 (828) 624-4249

What's Included

Seamless Gutter Installation — Start to Finish

We handle the full installation from measurement through debris cleanup. Your gutters are fabricated on-site from a continuous coil — cut to the exact length of your run at the job, not pre-cut at a shop. Every downspout is sized and placed for the drainage load it needs to carry.

Every Installation Includes:

Full measurement of all gutter runs and roofline
On-site fabrication — no pre-cut sections, no seams along runs
Removal and disposal of old gutters
Correct pitch set for each run — minimum ¼" per 10 feet of run
Hanger placement every 24" on center — not just at rafters
Downspouts sized, placed, and secured to wall with standoffs
End caps, miters, and outlet holes installed and sealed
Full flush test after installation
Debris cleanup at job close

New seamless gutter installation on Hickory NC home — Hickory Gutter Pros

Options

5-Inch or 6-Inch? K-Style or Half-Round? We'll Tell You What Your Home Needs.

The right gutter size depends on your roof pitch, drainage area, and canopy. We give you a specific recommendation at the estimate — not a one-size-up upsell.

5-Inch K-Style

Standard for most single-story Hickory-area homes with moderate roof pitch and average canopy. Handles up to approximately 5,500 sq ft of drainage area per downspout.

6-Inch K-Style

For steeper pitches, larger roof areas, concentrated drainage points, or homes under heavy tree cover. Handles approximately 7,950 sq ft per downspout — 45% more capacity.

½R

Half-Round

Traditional rounded gutter profile — common on older homes and architecturally appropriate for certain styles. Available in 5" and 6" with matching round downspouts.

🎨 30+ Colors Available

Standard gutter colors cover white, almond, cream, brown, clay, bronze, gray, and more. We'll match your fascia or soffit color at the estimate — bring a photo or color chip.

🔩 .032 Gauge Aluminum Standard

We install .032 gauge as standard — thicker than the .027 gauge used by budget installers. Heavier gauge holds form over longer runs, resists dents, and doesn't bow to create low spots.

💧 Hidden Hanger System

Gutters are hung with concealed screw-in hangers on 24" centers. No visible spikes — cleaner look, stronger hold, and no spike pull-out after a few years of freeze-thaw cycles.

Seamless gutter downspout installation — Hickory Gutter Pros

Why Seamless

Why Seamless Gutters Outperform Sectional Every Time

The most common gutter leak isn't from a hole in the bottom of the gutter — it's from a failed seam where two sections were joined. Every seam is a potential failure point. Seamless gutters eliminate all seams along the run, leaving only the necessary joints at corners and downspout connections. Fewer seams = fewer failures.

No Seam Leaks Along the Run

Sectional gutters joined with silicone eventually separate from thermal expansion, ladder contact, or debris impact. One continuous piece per run removes this failure mode entirely.

Better Appearance

A seamless run looks like a single element — no visible overlap joints breaking up the line. On long runs this is a significant visual difference.

Custom Length Every Time

On-site fabrication means your 47-foot east run gets a 47-foot piece — not a 40-foot piece plus a 10-foot splice. Exact fit, every run.

Installation Process

How a Seamless Gutter Installation Works

On-Site Estimate & Measurement

We measure every run, assess your roofline pitch, check your existing downspout drainage, and give you a fixed written price with the recommended size and color. No change orders on install day.

Old Gutter Removal

Existing gutters, brackets, and spikes are removed and disposed of. We inspect the fascia behind them for rot or damage — if we find any, we'll tell you before we reinstall anything over it.

On-Site Fabrication

Gutters are roll-formed on-site from an aluminum coil to the exact length of each run. One continuous piece per run — no shop cuts, no pre-cut inventory to fit to.

Pitch Setting & Hang

Gutters are hung at the correct pitch — typically ¼" of drop per 10 feet of horizontal run toward the downspout. Hangers are set on 24" centers. On longer runs we set the endpoint marks first, then string the line for consistent pitch along the entire run.

Downspouts, End Caps & Flush Test

Downspouts are sized and secured with standoffs, all end caps and miters are installed and sealed, and we run water through the full system before we leave. You see it flowing correctly at job close.

📌 Bundle and Save

Installing New Gutters? Add Guards at the Same Time

New installation is the best time to add guards — the gutters are already being set up clean and correctly pitched. As a registered RainDrop® installer, we can bundle guard installation with any new gutter job for the best combined price. The 20-year warranty applies to the guards regardless.

Learn About RainDrop® Guards →

FAQ

Gutter Installation Questions & Answers

Seamless gutters are custom-fabricated on-site from a continuous aluminum coil — there are no seams along the run, only at corners and downspout connections. This eliminates the most common failure point of sectional gutters: seam leaks. Gutters are cut to the exact length of each run at your home.

For most single-story Hickory-area homes, 5-inch K-style gutters are sufficient. Homes with steep roof pitches, large roof surfaces, or concentrated flow points often benefit from 6-inch. We assess your roof during the estimate and make a specific recommendation — we don't upsell size unless the run genuinely needs it.

We install .032 gauge aluminum as standard — a step up from the .027 gauge used by many budget installers. Heavier gauge holds its form better, resists dents from ladder contact, and stays true over longer runs without the subtle bowing that creates low spots.

Yes. We carry a full range of standard gutter colors. Bring us a photo or gutter chip and we'll match as closely as possible. For exact color matching on partial replacements, we identify the existing color at the estimate.

New gutter installation is the ideal time to add guards — the gutters are already clean and correctly pitched, and the labor overlap keeps the combined cost lower than two separate projects. As a registered RainDrop® installer, we can bundle guard installation with any new gutter job.